Robbe Modellsport Monsun V3 PNP+ Styrofoam/GRP/Abachi, white Incl. motor, HV servos and 85A ESC
Product number:
2718
€999.99*
Not in stock. Available approx. from 28.08.2026 to 27.09.2026.
Robbe Modellsport RO-SAFETY LIPO SAFE TRANSPORT AND CHARGING CASE FOR LIPO BATTERY
€75.99*
€79.99*(5% saved)
- Model Monsun V3 almost ready to fly prefabricated
- in mold painted GRP/CfK fuselage
- ready-covered, Styro/GfK/Abachi wing
- ready covered, removable T-tail made of balsa
- with built-in Ro-Power Torque 3526-870 motor
- with built-in Ro-Control 85A LITE ESC
- with built-in two Robbe FS-288+ servos with softstart
- with built-in four Robbe FS-288+ servos with softstart
- aluminum spinner 38mm and CfK propeller 12x8"
- small parts (rudder horns, linkages, clevises, covers, etc.), but already completely installed
- Assembly instructions in German/English/French
| Wing-span (mm): | 3000 |
|---|---|
| Flight weight approx. (g): | 2950 |
| Control: | Ailerons, Elevator, Flaps, Motor Powered, Rudder |
| Length (mm): | 1480 |
| Manufacturer: | Robbe Modellsport |
| Fuselage: | Carbon/FiberGlass |
| Wings: | Styro/Fiberglass/Abachi |
| Rec. engine: | Ro-Power Torque 3526-870kv |
| Rec. Battery: | 4S/4200mAh LiXX |
| Version: | PNP+ - PLUG N PLAY |
| Airfoil: | HQ 2,5/9 |
| Flight Skill: | Advanced |
| Build Skill: | Beginners |
| Drive Type: | Electric |
The MONSUN V3 is the successor and the further development of the famous MONSUN V2. It is a thermal and all-round glider in the compact 3m class with 4-flap wing. The T-tail is hinged backlash-free with a directly installed servo.
The PNP+ version has servos already installed, electrical connector and original multilocks as wing locks.
The flight characteristics are very good-natured. The MONSUN V3 can be flown as a slow thermal glider or as an all-rounder.
The ready-covered wings are constructed of styro core, glass fiber layers, abachi planking and a carbon fiber reinforced spar. The ratio of weight and strength has been optimally achieved.
The MONSUN V3 is suitable for advanced model pilots.
Features:
The PNP+ version has servos already installed, electrical connector and original multilocks as wing locks.
The flight characteristics are very good-natured. The MONSUN V3 can be flown as a slow thermal glider or as an all-rounder.
The ready-covered wings are constructed of styro core, glass fiber layers, abachi planking and a carbon fiber reinforced spar. The ratio of weight and strength has been optimally achieved.
The MONSUN V3 is suitable for advanced model pilots.
Features:
- two-part, ready Styro/GfK/Abachi wing with CfK connector
- continuous sandwich spar (carbon-pine-carbon) for maximum bending stiffness
- built-in digital Robbe servos FS-82 HV MG ECO with softstart, ball bearings and metal gearbox
- ready-made wiring of all servos with MPX 6-pin connectors between wing and fuselage
- ready ironed rudder flaps with mounted rudder horns
- in mold painted GRP fuselage with built-in wooden formers and CfK reinforcements
- powerful Ro-Power Torque 3526 870 K/V outrunner, optimized for 4S
- built-in Ro-Control 85A LITE ESC
- large canopy for easy battery change and RC installation
- ready hinged rudder flaps
- prefabricated rudder linkages with linkage parts from German production
- pre-cut servo well and linkage covers
- anodized 38mm aluminum spinner with straight center section
- high-strength carbon fiber airscrew 12x8"
- modern, highly visible design
Manufacturer and responsible person (information obligations under the GPSR Product Safety Regulation)
Modellbau Lindinger GmbH
Industriestraße 10
4565 Inzersdorf
ÖSTERREICH
Telefon: +43/7582/81313-0
[email protected]