Robbe Modellsport Monsun V2 ARF Styro/GfK/Abachi Surface
Product number:
2663
Robbe Modellsport RO-POXY 5 MINUTES EPOXY RESIN ADHESIVE 200G PER 100G RESIN+HARDENER
Content: 0.2 kg (€78.00* / 1 kg)
€15.60*
- Monsun V2 model largely prefabricated
- Painted fiberglass/carbon fuselage
- Ready-made covered Styro/GRP/Abachi wing
- Ready-made covered, removable T-tail made of balsa
- Small parts (rudder horns, linkages, clevises, ball heads, covers, etc.)
- Assembly instructions in German/English/French
| Wing-span (mm): | 3000 |
|---|---|
| Flight weight approx. (g): | 2950 |
| Control: | Ailerons, Elevator, Flaps, Motor Powered, Rudder |
| Length (mm): | 1480 |
| Manufacturer: | Robbe Modellsport |
| Fuselage: | Carbon/FiberGlass |
| Wings: | Styro/Fiberglass/Abachi |
| Rec. engine: | Ro-Power Torque 3526-870kv |
| Rec. Battery: | 4S/4200mAh LiXX |
| Version: | ARF - ALMOST READY TO FLY |
| Airfoil: | HQ 2,5/9 |
| Flight Skill: | Advanced |
| Build Skill: | Advanced |
| Drive Type: | Electric |
The MONSUN V2 is the successor and the further development of the famous MONSUN. It is a thermal and all-round glider in the compact 3m class with 4-flap wing. The T-tail is hinged backlash-free with a directly installed servo.
The PNP+ version has servos already installed, electrical connector and original multilocks as wing locks.
The flight characteristics are very good-natured. The MONSUN V2 can be flown as a slow thermal glider or as an all-rounder.
The ready-covered wings are constructed of styro core, glass fiber layers, abachi planking and a carbon fiber reinforced spar. The ratio of weight and strength has been optimally achieved.
The MONSUN V2 is suitable for advanced model pilots.
Features:
The PNP+ version has servos already installed, electrical connector and original multilocks as wing locks.
The flight characteristics are very good-natured. The MONSUN V2 can be flown as a slow thermal glider or as an all-rounder.
The ready-covered wings are constructed of styro core, glass fiber layers, abachi planking and a carbon fiber reinforced spar. The ratio of weight and strength has been optimally achieved.
The MONSUN V2 is suitable for advanced model pilots.
Features:
- two-part, ready Styro/GfK/Abachi wing with CfK connector
- continuous sandwich spar (carbon-pine-carbon) for maximum bending stiffness
- built-in digital Robbe servos FS-82 HV MG ECO with softstart, ball bearings and metal gearbox (PNP+ only)
- ready-made wiring of all servos with MPX 6-pin connectors between wing and fuselage (PNP+ only)
- ready ironed rudder flaps with mounted rudder horns
- painted GRP fuselage with built-in wooden formers and CfK reinforcements
- powerful Ro-Power Torque 3526 870 K/V outrunner, optimized for 4S (PNP+ only)
- built-in Ro-Control 60A ESC (PNP+ only)
- large canopy for easy battery change and RC installation
- ready hinged rudder flaps
- prefabricated rudder linkages with linkage parts from German production
- pre-cut servo well and linkage covers
- anodized 38mm aluminum spinner with straight center section (PNP+ only)
- high-strength Falcon carbon fiber airscrew 12x8" (PNP+ only)
- modern, highly visible design
Manufacturer and responsible person (information obligations under the GPSR Product Safety Regulation)
Modellbau Lindinger GmbH
Industriestraße 10
4565 Inzersdorf
ÖSTERREICH
Telefon: +43/7582/81313-0
[email protected]